Building it? The $29 builder's plan dimensions every stud, sheet and cut. See sample sheets
Planner checks
13 applicable rated checks passed for this configuration.
Site-specific requirements are not fully assessed. The checks size the structure and the vent openings at 20 psf of snow; they do not predict the temperature or humidity inside. Each bar is what this design asks of a part against its limit: the rafter span, the snow the sheets are tabled for, the vent area or fan airflow, and the aisle. The open part of the bar is room this design does not use.
Rafter span, 2x65' 8-1/2"of 12' 5-11/16" allowed54% of the allowed span unused at 20 psf; deflection governs
Snow on the glazing20 psfof about 31 psf in the maker's table35% of the tabled load unused for this sheet
Roof vents43 sq ftfor 38.4 sq ft needed22% of the floor; the rule asks 20%
Side vents38.5 sq ftfor 38.4 sq ft needed20% of the floor; the rule asks 20%
Aisle73"for 24" suggested49" wider than the suggested aisle
what this design asks room to spare
Green meets the maker's table or the extension guide we checked against, amber asks you to confirm something before you buy, red is outside it. Planner checks don't replace your local building department or a look at your own site.
The glazing maker's sheet spacing at 16 psf (our default for a sheltered site); the sheet span only, the frame and the anchors are not designed for wind
Pre-drill each hole about 2 mm (5/64 in) wider than the screw: 1/4 in for a #9, 9/32 in for a #10, 5/16 in for a #12, EPDM washers, do not crush the washer; every 8 in where winds are high
8 ground anchors on a timber base; the base corners joined with A34 angles, the walls framed and sheathed in glazing, the rafters tied to the plates
Needed
Anchor every corner and along the sides (our default), a glazed frame is light and catches wind; not verified by this plan (hold point): the plan does not calculate wind on this greenhouse, so none of these is shown to hold it: the ground anchors in your soil, the joints of the base, the connections of the walls to the base and of the rafters to the walls, the racking (side to side) stiffness of the walls and the end walls, which have no diagonal bracing drawn, and the doors and vents under a gust; your building department or an engineer checks the whole frame for your site's wind before the walls go up
7 2x6 ties, one on every rafter pair between the end walls (24 in on center), 7 10d common nails at each heel
Needed
4 16d common per heel in IRC Table R802.5.2(1) (5:12 row for this 6:12 roof, 24 in rafter spacing, 30 psf ground snow column (your 20 psf roof snow / 0.7 = 28.6 psf ground snow), 12 ft span column), x 1.2 for 10d common and / 0.7 for wet service = 7
Flat 2x4 door header DH, 37" long, its ends bearing 1-1/2" on a jack stud each side (35-1/2" jack center to jack center), carrying the cripple DC under the roof framing: 40 lb on it in all, 20 lb at the more loaded end
Needed
Spruce-Pine-Fir No. 2 laid flat, wet service, snow load duration (NDS Supplement 2018 Table 4A, flat use factor 1.1): bending 268 psi of 1411 allowed, shear 6 psi of 151, deflection 0.025 in of 0.147 in under the snow (L/240, IRC R301.7 for other structural members), all the cripple loads added together; bearing on each jack stud 4 psi of 285 allowed across the grain (Fc-perp 425 psi x wet service 0.67, on 5.25 sq in), the jack carrying it down to the bottom plate, as IRC R602.7 frames a header on jack studs; each cripple's load is (roof snow, at least 10 psf, + 4 psf dead) x 12-3/8" of roof the end rafter carries x half the run to the next support either side (40 lb at 17-3/4" from the left jack center)
2 10d common toe-nails at each end of every purlin block and vent header and sill, from the top at the end toward the door end wall (1-3/8" from the end, 30 degrees) and from below at the other end (1-1/2", 25 degrees): 133 lb allowed at each end (66 lb a nail)
Needed
54 lb at the most loaded end (a vent header or sill 22-1/2" long carrying 27-1/2" of the slope and half its lid, 4 lb, at (roof snow, at least 10 psf, + 4 psf dead), half to each end); NDS 2018 nail yield limit for a 10d common in spruce-pine-fir, 1-5/8" of shank in the block and 1-3/8" in the rafter, toe-nail factor 0.83, snow load duration 1.15, wet service 0.7
8 roof vents (43 sq ft) and 11 side vents (38.5 sq ft), automatic openers
Door
32" x 76" site-built and glazed, in the front gable
Benches
2 x 30" deep, 73" aisle
The frame
Rafters
2x6 at 24"
Studs
2x4 at 24"
Base
24" knee wall
Roof supports
24" max apart
Rafters
18 2x6 rafters 24" on center
Ridge
2x8, 16'
Rafter ties
7 across the gable at plate height
Wall girts
at most 24" apart up the walls
Base
8 ground anchors; gravel bed 14' x 18', 4" deep
Sheets
1 x 8 ft, 6 x 10 ft, 9 x 12 ft
Cost and time
What it takes to build.
Greenhouse materials, before the gravel bed$6,604.68
Polycarbonate and profiles$3,366.68
Vents, door and hardware$1,575.10
Frame lumber$1,366.04
Base$296.86
Shelf prices from Home Depot, Hamilton Mill store; Lowe's, Atlanta-Edgewood store; Steve Regan Company (steveregan.com); PolycarbonateStore.com; Greenhouse Megastore; Home Depot, Bronx Terminal store; Fence and Lumber; Home Depot, ship to store; Sturdi-Built Greenhouse; Amazon.com, shipped, read Sep 30, 2026 to Nov 21, 2026. Before sales tax, delivery and tools.
Every priced line of the materials list has a store price. Prices as read at Home Depot, Hamilton Mill store; Lowe's, Atlanta-Edgewood store; Steve Regan Company (steveregan.com); PolycarbonateStore.com; Greenhouse Megastore; Home Depot, Bronx Terminal store; Fence and Lumber; Home Depot, ship to store; Sturdi-Built Greenhouse; Amazon.com, shipped, between Sep 30, 2026 and Nov 21, 2026, before tax and shipping. Gravel is a sourced range from HomeGuide, crushed stone and gravel prices (Dec 2025), kept apart from the priced total.
Not included: gravel (estimated separately at $108 to $353); tax; shipping or freight. Twin-wall sheets usually ship by freight, which can add a lot: get a delivered quote.
Per sq ft of floor
$34.40
Gravel bed, separate
est. $108 to $353
Build time
79 to 114 h
one handy person with a helper (our estimate)
If you hire the build
$3,950 to $11,400
Separate from the materials.
Lumber$1,366.04
2 boards
4x4 PT x 12 ft4 in. x 4 in. x 12 ft. #2 Pressure-Treated Ground Contact Southern Pine Timber
$41.76
2 boards
4x4 PT x 16 ft4 in. x 4 in. x 16 ft. #2 Pressure-Treated Timber
$55.76
1 board
2x4 PT x 8 ftWeatherShield 2 in. x 4 in. x 8 ft. #2 Prime Ground Contact Pressure-Treated Southern Yellow Pine Lumber
$4.88
5 boards
2x4 PT x 10 ftWeatherShield 2 in. x 4 in. x 10 ft. #2 Prime Ground Contact Pressure-Treated Southern Yellow Pine Lumber
$41.90
2 boards
2x4 PT x 12 ftWeatherShield 2 in. x 4 in. x 12 ft. #2 Prime Ground Contact Pressure-Treated Southern Yellow Pine Lumber
$20.16
21 boards
2x4 PT x 16 ftWeatherShield 2 in. x 4 in. x 16 ft. #2 Prime Ground Contact Pressure-Treated Southern Yellow Pine Lumber
$310.38
56 boards
2x4 x 8 ft2 in. x 4 in. x 96 in. #2 Premium Grade KD-HT Stud
$238.00
5 boards
2x4 x 10 ft2 in. x 4 in. x 10 ft. #2 Grade SPF Dimensional Lumber
$36.80
3 boards
2x4 x 12 ft2 in. x 4 in. x 12 ft. #2 Premium Grade SPF Dimensional Lumber
$26.52
7 boards
2x4 x 16 ft2 in. x 4 in. x 16 ft. #2 Grade SPF Dimensional Lumber
$82.46
18 boards
2x6 x 8 ft2 in. x 6 in. x 8 ft. #2 Premium Grade SPF Dimensional Lumber
$155.16
7 boards
2x6 x 12 ft2 in. x 6 in. x 12 ft. #2 Premium Grade SPF Dimensional Lumber
$90.44
1 board
2x8 x 16 ft2 in. x 8 in. x 16 ft. #2 Prime Southern Yellow Pine Kiln-Dried Lumber
$21.12
13 boards
1x4 x 8 ftPrimeLinx 1 in. x 4 in. x 8 ft. Radiata Pine Finger Joint Primed Board
$132.86
4 boards
1x4 x 12 ftTrim Board Primed Finger-Joint (Common: 1 in. x 4 in. x 12 ft.; Actual: .719 in. x 3.5 in. x 144 in.)
$64.92
2 boards
1x4 x 16 ftCMPC 1 in. x 4 in. x 16 ft. Radiata Pine Finger Primed Softwood Boards
$42.92
Glazing$2,425.58
1 sheet
Palram SUNLITE 8 mm twin-wall polycarbonate, 4 x 8 ftPalram Sunlite Twinwall Polycarbonate Greenhouse Panel, Clear, 4 x 8 ft, 8 mm
$104.99
6 sheets
Palram SUNLITE 8 mm twin-wall polycarbonate, 4 x 10 ftPalram Sunlite Twinwall Polycarbonate Greenhouse Panel, Clear, 4 x 10 ft, 8 mm
$777.72
9 sheets
Palram SUNLITE 8 mm twin-wall polycarbonate, 4 x 12 ftPalram Sunlite Twinwall Polycarbonate Greenhouse Panel, Clear, 4 x 12 ft, 8 mm
$1,542.87
Profiles and sealing$941.10
4 x 12 ft
H connector profile for 8 mm sheetPolycarbonate Joiner Cap (H Channel), Gallina
$124.08
7 x 6 ft
Base and cap connector: aluminum glazing bar and capAluminum glazing bar and glazing cap (bar and cap joint, in place of Palram's base and cap)
$165.48
59 x 8 ft
U end profile for 8 mm sheetPalram Sunlite 8 ft. U-Channel for 8 mm sheet
Ridge cap: polycarbonate R channel for 8 to 10 mm sheetPolycarbonate Corner Cap (R Channel), adjusts to the ridge angle
$109.90
4 tubes
Clear silicone, polycarbonate-safeGE Supreme Silicone 10.1-oz Window and Door Clear Silicone Caulk
$53.92
Fasteners and hardware$666.06
7 packs of 100
Polycarbonate screws with EPDM washersTacoma Screw Washer Head Screws, zinc-plated, EPDM washer, hex head
$279.65
2 packs of 900
Exterior wood screws, 3 inEverbilt #9 x 3 in. Tan Star Torx Drive Flat Head Wood Deck Screw (900-Pack)
$49.76
18 ties
Rafter-to-plate tie (H2.5A)Simpson Strong-Tie H2.5A 18-Gauge ZMAX Galvanized Hurricane Tie
$17.64
3 boxes
Simpson connector screws, #9 x 1-1/2 in (SD9112), boxes of 100Simpson Strong-Tie #9 x 1-1/2 in. 1/4-Hex Drive, Strong-Drive SD Connector Screw (100-Pack)
$49.95
1 1 lb box of 62
10d common nails, hot-dip galvanized (0.148 x 3 in), for the door framingGrip-Rite 3-in 9-Gauge Hot-dipped galvanized Smooth Shank Common Nails, 62 per box (1 lb)
$7.98
8 1s lb box of 62
10d common nails, hot-dip galvanized (0.148 x 3 in), for the rafter ties, seats and ridge, purlin blocksGrip-Rite 3-in 9-Gauge Hot-dipped galvanized Smooth Shank Common Nails, 62 per box (1 lb)
$63.84
26 packs
Flat corner braces, 2 in, 4-packsEverbilt (4-Pack) 2 in. Zinc-Plated Flat Corner Brace
$82.42
1 box
Screws for the corner braces, #6 x 5/8 in, box of 1000#6 x 5/8 in. Black Phillips Flat Head Coarse Thread Screws (1000 per Box)
$14.86
2 gal
Exterior paint, white, for the frameBEHR PREMIUM PLUS 1 gal. #52 White Satin Enamel Exterior Paint & Primer
$99.96
Vents and door$909.04
21 2-packs
Strap hinges, 3 inNational Hardware 3-in Zinc plated Strap Interior/Exterior Door Hinge 2-Pack
$100.38
1 latch
Two-sided door latchGH Gate Products Black All-In-One Two Sided Gate Latch (opens from both sides)
Automatic vent opener (wax cylinder, no power)Bayliss Automatic Vent Opener (MK7), single spring
$719.92
Base and site$296.86
4 angles
Simpson A34Z framing angle, for the base cornersSimpson Strong-Tie A34Z Framing Angle, 1-7/16 in W, 2-1/2 in D, Steel, ZMAX
$7.96
2 kits
Ground anchor kit (4 anchors)Tie Down Engineering 59075 Galvanized Cable Kit (4 anchors, 8 clamps, 100 ft galvanized cable)
$101.78
4 sheets
T1-11 siding panel 4x8 for the knee wallPlytanium Plywood Siding Panel T1-11 8 IN OC (Nominal: 19/32 in. x 4 ft. x 8 ft.)
$187.12
3.75 cu yd
Gravel bed under the base, compactedestimate, kept apart from the total
est. $56 to $281
1.8 cu yd
Floor: pea gravel over landscape fabric, 3 in (optional)estimate, kept apart from the total
est. $52 to $72
$6,755 at the middle rate of $70 per hour times 97 hours. The range is the published hourly rates of $50 to $100 times our 79 to 114 hour build estimate: 79 hours at $50 to 114 hours at $100 (Fixr, Jan 31, 2025: $70 per hour; HomeAdvisor, Jun 19, 2026: $50 to $100 per hour). A sourced range for building the greenhouse from plans, by a handyperson or carpenter, not a quote, kept apart from the materials. No published guide gives a labor price for building a custom greenhouse from plans, so this is an hourly rate times our build-hours estimate. The hours are ours, for one handy person with a helper.
Prices differ by store and by week: change any line in the greenhouse cost calculator to get your own total.
Free and paid, side by side
Design it free. Build it from the $29 plan.
Free
On this page and in the designer, no account
This design in 3D, and every change you make to it
Every planner check, with its rule and source
Cost estimate
About $6,605 in materials, line by line, on this page. See the estimate
Summary PDF
The design, its checks and its materials list on a few pages. A summary, not the build drawings.
You check out in the designer, with this design loaded. If the plan has an error, we fix it or refund you within 30 days. Guarantee terms.
Real sheets from the 41-sheet sample plan for the 8x12 gable greenhouse
The sample was printed on an earlier date, so its prices can differ from the estimate above. Your plan prints the same prices as the estimate.
Wall framing
Sheet layout
Cut list
Build sequence
Build phases
From gravel bed to the last vent in 6 phases.
About 79 to 114 hours for one handy person with a helper (our estimate). Each picture is this design at the end of its phase, drawn by the designer, with that phase's parts in full color.
01
Gravel bed and base
Level the gravel bed, lay the treated base timbers, square them and anchor them. Check: diagonals equal within 1/4 in, base level.
02
Knee wall and wall frames
Frame each wall flat, stand it, plumb and brace it, then screw the corners and the bottom plates to the base. Side the knee wall up to the glazing line. Check: corners plumb both ways, top plates level.
03
Roof frame
Set the ridge, rafters, ties and purlins. Paint the frame white before any sheet goes on. Check: rafter tops in one plane: a string along them touches each one.
04
Door and benches
Hang the door and build the benches while the house is still open. Check: door swings clear, benches level.
05
Twin-wall glazing
Walls first, then the roof from the door end, each sheet taped and capped, flutes running down. Check: every hole pre-drilled, washers snug, not crushed.
06
Vents and auto openers
Hang the vent lids and fit the automatic openers. Check: each lid closes flat and opens fully.
This is the summary. The $29 builder's plan breaks these phases into a build order with the new parts highlighted, a how-to detail and a check at each step.
For this design the priced materials come to $6,604.68 at the store prices on this page, before sales tax and freight. The gravel bed is estimated apart, at $108 to $353. If you hire the build, published hourly rates times our hour estimate give $3,950 to $11,400 for labor. The total moves with the size, the glazing and the vents you pick in the designer.
We have not priced kits, so we cannot say which is cheaper for you. What we can say: building this 12x16 yourself from the plan costs $6,604.68 in priced materials plus your time. Compare that with a kit of the same floor area at its delivered price, and check what the kit's glazing and frame are rated for.
It depends on your town. The model building code exempts small one-story detached accessory buildings up to 200 sq ft, and this design is 192 sq ft, but many towns use a lower limit or treat greenhouses differently, and setbacks still apply. Ask your building department before you order materials.
This design uses 8 roof vents (43 sq ft of opening) and 11 side vents (38.5 sq ft): cool air comes in low and leaves near the ridge. We draw roof vents of at least 20% of the floor, the ASABE figure cited by extension guides. Wax-cylinder openers open the lids without power.
It is drawn for the 20 psf you see on this page. 8 mm twin-wall sheets are tabled by the maker to about 31 psf, so the planner turns red above that. Use the roof snow load your building department gives you, and clear heavy snow after storms.
Roof vents near the ridge let warm air out; side vents above the benches let cool air in. On a gable the two long walls have room for every side vent the floor needs.
This gable, 192 sq ft of floor
12x16 gable
Vents of the 12x16 gable
Vents
Count
Opening
Roof vents, both slopes
8
43 sq ft
Side vents, both long walls
11
38.5 sq ft
Side vents, end walls
0
0 sq ft
Roof, drawn / needed
43 / 38.4 sq ft
Sides, drawn / needed
38.5 / 38.4 sq ft
We draw roof vents of at least 20% of the floor and side vents of at least 20%, the ASABE figures cited by UConn and Alabama Extension. Areas are the openings in the frame; how much air moves also depends on how far each lid opens.
Your greenhouse, your numbers
Make the 12x16 yours.
Change the size, the roof, the glazing, the vents and the benches. The roof supports, the vents and the materials list follow every change. Free, no account.